Research Article
BibTex RIS Cite
Year 2023, Volume: 6 Issue: 2, 31 - 40, 30.12.2023
https://doi.org/10.38061/idunas.1358218

Abstract

References

  • 1. Arslan, A., Masjuki, H. H., Kalam, M. A., Varman, M., Mufti, R. A., Mosarof, M. H., Khuong, L. S., Quazi, M. M. (2016). Tribological Effect of Surface Texturing on Cutting Tool Performance: A Review, Critical Reviews in Solid State and Materials Sciences, 41; 448-481.
  • 2. Canel, T., Kaya, A.U., Celik, B. (2012). Parameter optimization of nanosecond laser for microdrilling on PVC by Taguchi method, Optics & Laser Technology, 44; 2347–2353.
  • 3. Canel, T., Zeren, M. Sınmazcelik, T. (2019). Laser parameters optimization of surface treating of Al 6082-T6 with Taguchi method, Optics and Laser Technology, 120; 105714.
  • 4. Crouch I. G., Cimpoeru, S. J., Shanmugam D., Li, H. (2017). Armour steels, The Science of Armour Materials Woodhead Publishing in Materials, 55-115.
  • 5. Khundyakov, A., Vaschennko, S., Banasiewicz, A., Wroblewski, A. (2021). Materials Selection and Design Options Analysis for a Centrifugal Fan Impeller in a Horizontal Conveyor Dryer, Materials, 14; 6696.
  • 6. Konat, L. (2021). Technological, Microstructural and Strength Aspects of Welding and Post-Weld Heat Treatment of Martensitic, Wear-Resistant Hardox 600 Steel, Materials, 14; 4541.
  • 7. Kuntoglu, M. (2022). Machining induced tribological investigations in sustainable milling of Hardox 500 steel: A new approach of measurement science, Measurements, 201; 111715.
  • 8. Korkmaz., M. E. Gupta, M.K., Ross, N. M., Sivalingam, V., (2023). Sustainable Materials and Technologies, 36; e00641
  • 9. Ligier, K., Zemlik, M., Lemecha, M., Konat, L., Napiorkowski, J. (2022). Analysis of Wear Properties of Hardox Steels in Different Soil Conditions, Materials, 15; 1-18.
  • 10. Ramezani, M., Ripin, Z. M., Passang, T., Jiang, C. (2023). Surface Engineering of Metals: Techniques, Characterizations and Applications, Metals, 13; 1299.
  • 11. Sahooa, S. K., Thirupathi, N., Saraswathamma, K. (2020). Experimental Investigation and Multi-Objective Optimization of Die sink EDM Process Parameters on Inconel-625 alloy by using Utility Function Approach, Materials Today: Proceedings 24; 995–1005.
  • 12. Tarng, Y.S., Yang, W.H. (1998). Optimization of the weld bead geometry in gas tungsten arc welding by the Taguchi method, Int. J. Adv. Manuf. Technol. 14; 549–554.
  • 13. Wang, W., Qi, L. (2019). Light Management with Patterned Micro- and Nanostructure Arrays for Photocatalysis, Photovoltaics, and Optoelectronic and Optical Devices, Advanced Multifunctional Materials, 29; 1807275.
  • 14. Yang, W.H, Tarng Y.S. (1998). Design optimization of cutting parameters for turning operations based on the Taguchi method. Journal of Materials Processing Technology 164;122-129.

Using CO2 Laser, Optimization of Laser Power, Exposure Time and Frequency for Cavity Formation on Hardox Steel Plate

Year 2023, Volume: 6 Issue: 2, 31 - 40, 30.12.2023
https://doi.org/10.38061/idunas.1358218

Abstract

The texture of the surfaces of materials causes changes in mechanical properties such as friction. Micro-scale cavities have been created on Hardox steel plate, which has recently been the focus of attention in demanding applications with its hardness, toughness and wear resistance. CO2 laser was used in the cavitation process on the surface and the power, exposure and frequency of the laser used were optimized to obtain a cavity with the desired geometry. Taguchi method was used in the optimization process. In addition to obtaining the optimum parameters, the effect ratios of the parameters were also calculated. Optimum laser parameters were obtained as 5 s for laser exposure duration, 60 W for laser power, and 50 kHz for laser frequency. According to the optimization calculations, the parameter with the highest effect on the result was laser exposure duration with a rate of 71,86 %. Laser power and laser frequency affected the result by 23.02 % and 5.12 % respectively.

References

  • 1. Arslan, A., Masjuki, H. H., Kalam, M. A., Varman, M., Mufti, R. A., Mosarof, M. H., Khuong, L. S., Quazi, M. M. (2016). Tribological Effect of Surface Texturing on Cutting Tool Performance: A Review, Critical Reviews in Solid State and Materials Sciences, 41; 448-481.
  • 2. Canel, T., Kaya, A.U., Celik, B. (2012). Parameter optimization of nanosecond laser for microdrilling on PVC by Taguchi method, Optics & Laser Technology, 44; 2347–2353.
  • 3. Canel, T., Zeren, M. Sınmazcelik, T. (2019). Laser parameters optimization of surface treating of Al 6082-T6 with Taguchi method, Optics and Laser Technology, 120; 105714.
  • 4. Crouch I. G., Cimpoeru, S. J., Shanmugam D., Li, H. (2017). Armour steels, The Science of Armour Materials Woodhead Publishing in Materials, 55-115.
  • 5. Khundyakov, A., Vaschennko, S., Banasiewicz, A., Wroblewski, A. (2021). Materials Selection and Design Options Analysis for a Centrifugal Fan Impeller in a Horizontal Conveyor Dryer, Materials, 14; 6696.
  • 6. Konat, L. (2021). Technological, Microstructural and Strength Aspects of Welding and Post-Weld Heat Treatment of Martensitic, Wear-Resistant Hardox 600 Steel, Materials, 14; 4541.
  • 7. Kuntoglu, M. (2022). Machining induced tribological investigations in sustainable milling of Hardox 500 steel: A new approach of measurement science, Measurements, 201; 111715.
  • 8. Korkmaz., M. E. Gupta, M.K., Ross, N. M., Sivalingam, V., (2023). Sustainable Materials and Technologies, 36; e00641
  • 9. Ligier, K., Zemlik, M., Lemecha, M., Konat, L., Napiorkowski, J. (2022). Analysis of Wear Properties of Hardox Steels in Different Soil Conditions, Materials, 15; 1-18.
  • 10. Ramezani, M., Ripin, Z. M., Passang, T., Jiang, C. (2023). Surface Engineering of Metals: Techniques, Characterizations and Applications, Metals, 13; 1299.
  • 11. Sahooa, S. K., Thirupathi, N., Saraswathamma, K. (2020). Experimental Investigation and Multi-Objective Optimization of Die sink EDM Process Parameters on Inconel-625 alloy by using Utility Function Approach, Materials Today: Proceedings 24; 995–1005.
  • 12. Tarng, Y.S., Yang, W.H. (1998). Optimization of the weld bead geometry in gas tungsten arc welding by the Taguchi method, Int. J. Adv. Manuf. Technol. 14; 549–554.
  • 13. Wang, W., Qi, L. (2019). Light Management with Patterned Micro- and Nanostructure Arrays for Photocatalysis, Photovoltaics, and Optoelectronic and Optical Devices, Advanced Multifunctional Materials, 29; 1807275.
  • 14. Yang, W.H, Tarng Y.S. (1998). Design optimization of cutting parameters for turning operations based on the Taguchi method. Journal of Materials Processing Technology 164;122-129.
There are 14 citations in total.

Details

Primary Language English
Subjects Materials Engineering (Other)
Journal Section Articles
Authors

Timur Canel 0000-0002-4282-1806

Satılmış Ürgün 0000-0003-3889-6909

Publication Date December 30, 2023
Acceptance Date December 7, 2023
Published in Issue Year 2023 Volume: 6 Issue: 2

Cite

APA Canel, T., & Ürgün, S. (2023). Using CO2 Laser, Optimization of Laser Power, Exposure Time and Frequency for Cavity Formation on Hardox Steel Plate. Natural and Applied Sciences Journal, 6(2), 31-40. https://doi.org/10.38061/idunas.1358218